How to Put Grip Tape on a Skateboard Perfectly

Skateboard grip tape is a gradual section of the skateboard layout that grip tape equips the rider with rubbing between their deck and shoes, which in turn holds the driver in place to balance the board while skating.

The tape on your skateboard is important for the foot material and offers on the off chance that you don’t know how to put different tape on your skateboard deck.

how to put grip tape on a skateboard

Guarantee that you have received the original notice for specific components of skateboard hold tape, for example, its structure, dimensions, adhesive properties, and non-bubble applications. These variables may affect your presentation capacity.

Most Effective Method to Put Grip Tape

1. You have to guarantee that you have these things; grip tape, deck, cross head screwdriver, and a cover shaper blade.

2. You spread the level surface skateboard at that time, ideally, a story or table to maintain a strategic distance from an accident guarantee that its realistic side is below!

3. At this point, you have to unscrew the clipped side and peel off the back paper from the grip tape that you will place on the front line of your deck.

4. Guarantee that the skateboard deck is secured to start!

5.  At that point, the normal strategy is to start from one side by permitting one finish of the holding tape to adhere to the tail or nose of the board.

6. At this point, you will begin pressing one finish of the board to adhere to the board’s deck and utilize your hand to press the tape to the center of the skateboard to guarantee that you have pulled out any air holes!

7.  You will then press the remaining piece of grip tape onto the board and guarantee that you are applying pressure to the board.

8. You should currently be up to date as the deck is fully secured, and perhaps at this stage, the grip tape should be covered by a double-check with no air bubbles!

9. The following step is to expel the over brands grip tape that covers the deck.

Read more: How to Reach the Exact Backpack for Skateboarding

10. First, you have to stamp the edge of the grip tape so that your grit is easier, as it runs as a rule.

11. Utilize the screwdriver pictured earlier and scratch along the edge of the deck on grip tape, you should see the bottom line as found in the picture below.

12. You need to tackle the cover shaper as pictured before and cut around the covering grip tape with the rules you have recently created. If you guarantee that it’s done on a level surface for good reason!

13. To make it easy enough for the lip of the holding tape to be covered against the edge of the skateboard as opposed to trying to work the outside of the grip tape.

14. As you cut the following lines, try to remove the guarantee that you are not prone to an accident.

15. After the holding tape is sliced to size, you can utilize the overabundance grip tape to move the edges of the deck to smooth.

16. At that point, the last step is to make a gap in your equipment that will join the deck in your truck.

17. You will need to utilize your screwdriver and a tool fastener and finely guarantee that you do not just press the grip tape through the softness and apply pressure slowly, you will experience.

18. When you’ve done this for each of the eight tool shaking regions, you should now have fully-applied grip tape on your skateboard deck!

The Size of a Skateboard Grip Tape

The most important variable you need to know before getting a skateboard grip tape is the measurement. Generally, for a traditional teahouse skateboard, you’ll need a size measurement of an event that is 33 x 9 inches that’s conveniently fit to fit the grip tape over your deck.


Do You Need Grip Tape On a Skateboard?

Grip tape is a fundamental part of the skateboard format, as it plays an important role in keeping your foot on the board, particularly when doing stunts. A few sheets come pre-held, while others don’t.

What are Skateboards With Grip Tape?

Grip tape is a sandpaper-like material that a glue back is applied to the highest point on a skateboard deck. Full skateboards were previously applied to hold tape. Grip tape will be applied for independently sold skateboard decks, and slices will be inserted for measurement.

Is Grip Tape Sandpaper?

Skateboard and longboard grip tape is comparable but not different from standard sandpaper. To start, as you say, there is glue on the back. Intense glue. Secondly, great quality grip tape should be unobtrusively more water-safe than traditional sandpaper.


All things considered, just the last word written on skateboard grip tapes is just plain that there are a few brands that need special attention before picking up, but it’s not a hassle.

Every grip tape has choices that are not difficult to put to your deck and anything else, or they have a type of feature, for example, better grains and apertures give you the ability to work more effectively.

Some elements must be considered, for example, to guarantee that the hold tape measure does not fit your deck correctly in any case!

Make sure to pick a fantastic realist or structure so that you hang on to the entertainment center which additionally allows you to feel good on a skateboard with the grip tape measurements offered.

Relevant Resources:

My name is Camila Avery. I like to write and share my experiences. HeartyLook is my lovely digital home, where I can share my professional advice, home improvement ideas, solution, beauty tips, product recommendations, and honest and open opinions on anything and everything.

Leave a Comment